Відео

What was that little machine that put the dents in the steel?? And why?

Looked really difficult, glad it turned out OK. Great job on going back until acceptable and then giving it a little extra! I don't see how all the folks are saying it was easy. It is easy to see on youtube!

16 years old bro 2024 love watching your vids come back

That was your fault you should never spray over a texture like that,plus if your using Laquer primer youre not getting nowhere it's gonna wrinkle everytime.

At 0.59 what is the machine and and what is the purpose for

The welder machine ?

What is the welder that you use

So glad Ohio doesn’t have those democrat inspections

TOP TIP for your shed, buy a LARGE polythene dust sheet and staple it to the walls and roof. You will stop ALL the dust and bugs then. Spray the shed floor with creosote two or more times. Any dust will stick to it, AND the floor won't rot. Bare metal with 80 grit, etch primer, epoxy primer, 240 grit. Filler, 400 grit, dolphin glaze, 600 grit, high build, 600 grit (WET), wash, high build mixed as sealer, 800 grit, base, 1000 to remove knibs, more base, 3 to 4 coats of clear then leave in the sun for a week or low bake. Cut, polish. DONE. THAT is how I did my bonnet. The finish is like glass and VERY chip and corrosion resistant.

Excellent video I may need to do this on my 1998 Honda prelude rear calipers. 71 retired lineman diyer also drive a 2006 Subaru sti

In the middle of doing the same swap! Definitely different from a ls1 swap but fun stuff! I’m just now getting into the wiring now

now that sir is impressive...butt welding flux core on a body panel?.. that is hard!... well done sir, well done

is that lap welded?... I'd be mightily impressed if that was butt welded on...

Awesome, thanks ❤

I really wish this dude still got on his UA-cam because I ask some questions so if anyone knows who this is could you tell him that I need to ask him some things please and thank you

Awesome. What paint brand did you use?

Hey this is some great work! What was the tool you used for creating an indentation line for the new quarter panel to rest on?

Did you run your fluxcore on high or low and what was the speed?

How much is a repair like this cost? I have a 1998 honda ek hatch dx model. 3 corners has rust.

Does my d16y8 vtec harness works on the h22? Or do I have to modify my harness?

I’m in the middle of removing the entire panel and replacing it with CF one. The middle of mine near the windshield was all dented up and didn’t want to deal with it anymore .

Hi. May I know what is the seal rubber size for the front set.. thanks

Gravy job with biscuit wheels 😂

What axles did you use

reall dope hard work man. good job. down to the threading where the bolts go , you brought all that back to life. this car body should easily last another 30 years or more

Who plays that music? I love it and would like to hear more of them!

Hope you're well and life is good. It's been a while, i really enjoyed your restoration build. Will you be back?

what brand is the electric joggler/edge setter? good video!

I have the Chicago Electric MIG 170... I'm not even sure they even make that model anymore, because I never see it in the store anymore, anyways, it works awesome & I'm glad I bought it when I did...the reason I didn't go for the cheaper flux core machine wasn't because I didn't think it would weld sheet metal, there's no doubt that it will, the problem, for me at least, is that the flux core can contaminate the weld & cause paint to fisheye...it doesn't happen all the time, but just the possibility of it makes me want to use the gas shielded MIG over the flux core...of course, if you aren't doing anything other than one or two patches, or maybe something structural, then, of course you want to go the cheapest way possible, certainly nothing wrong with that, but I wanted a bit more versatile welder, & for more than just one project, without having to pay over $500+ for it...

Would this be the same transmission the civic would have

great looking welds,thank you sir

Luxury indoor painting, I've got to do it on my driveway fighting wind, dust and insects 😀

What size is the circlip inside the piston?

How long did they last after you did all this work? was it worth the rebuild or would you have rather bought new ones?

Great job on welding but how you gonna protect that metal under your weld from rust? Your paint will not cover the bare metal that you bended before welding. Now rust will start forming inside where is metal on metal, and eventually it will come out on the outside under your paint. Any idea how to solve this problem?

In the same spot as my EK, thanks for the vid👌🏽✨

Hows it holding up now?

Good job. About To use my flux core on body panels. I just have to make them. I'm going to be using HOBART gasless flux-core .030 E71T-11

What was the air tool you used to fold the metal

Good job. I have an old Southbend lathe that needs finishing. After I sandblast everything and prep the metal, what 2k epoxy and high fill primer do you recommend? Thanks, Paul

Awesome job👍👍what amperage did you set your welder ❓my first car was a 1986 Honda Civic SI hatchback

How has it held up? Did the rust return?

.023 wire

Why didnt you wet sand the paint off?

The title says easy lol 😂😂😂😂😂 doesn't look easy

What kind of tool do you use for edge panel thank’s

I did this to my EK too! But you made much nicer brackets. I love the seats, but hated how high they sat. I ended up shaving a bunch of foam out of the seat bottom and taking out the spring under the seat. Got me about 2 inches of headroom back.

Nice work!